The HC-02 Bluetooth serial port module is based on version 2.0 development, high stability, ultra low power consumption, industrial grade Bluetooth digital transmission module. Users do not need to care about complex wireless communication configurations and transmission algorithms, just connect the device through a TTL serial port.
The HC-02 slave module is powered up and can be connected to the phone for data transfer. In addition, it can be connected to HC-05 or HC-06 host (match code, default is 1234), can replace the traditional serial cable, no wiring work, very flexible.
Model: HC-02
Working frequency band: 2.4G
Communication interface: UART 3.3V TTL level
Working voltage: 3V-3.6V
Baud rate: 1200~115200bps
Communication level: 3.3V
Transmit power: 6dBm (maximum)
Reference distance: 10 meters
Module size: 27 * 13mm
Airspeed: 2Mbps
Antenna interface: built-in PCB antenna
Communication current: 30mA
Receive sensitivity: -85dbm @ 2Mbps
Working humidity: 10%-90%
Storage temperature: -40 ° C ~ + 85 ° C
Working temperature: -25 ° C ~ + 75 ° C
Brief introduction to the working principle of the module
As shown in the figure above, the HC-02 module is used together with the HC-06 host to replace the physical connection during full-duplex communication. The device on the left sends the serial port data to the module. After receiving the serial port data, the RXD port of the module automatically sends the data to the air in the form of radio waves. The module on the right can be automatically received and the serial port data sent by the original left device is restored from TXD. The same is true from right to left.
Connection between module and MCU and other devices
As shown in the figure above,When the module is connected to the power supply system for the 3.3V MCU, the serial port can be cross-connected. (RX of the module is connected to the TX of the MCU, and the TX of the module is connected to the RX of the MCU)
When the module is connected to the 5V MCU of the power supply system, a 220 Ohm-1K Ohm resistor can be connected in series with the RX end of the module, and then the TX of the MCU is connected. The TX of the module is directly connected to the RX of the MCU, and no series resistor is needed. (Note: Please confirm that the MCU used determines the voltage of 3V as high level, otherwise it needs to add 3.3V/5V level conversion circuit)
Note: The power supply of the module is 3.3V (3~3.6V), it can't be connected to 5V, and directly connected to 5V will burn out the module! The 5V power supply must be stepped down by the LDO to 3.3V before powering the module.
Link between modules
HC-06 is the master, HC-02 is the slave, the pairing code is the same (the default is 1234), the baud rate is the same, and it can be automatically linked when the power is turned on. After the first connection, the HC-06 host will automatically remember the pairing object. If you need to connect other modules, you must first clear the pairing memory of the HC-06 host. There is no pairing memory in the slave.
Note:
Proprietary Service UUID: 49535343-FF7D-4AE5-8FA9-9FAFD205E455
TX UUID: 49535343-1 E4D-4BD9-BA61-23C647249616
RX UUID: 49535343-8841-43F4-A8D4-ECBE34729BB3
Module connection to PC
The HC-02 connected to the computer needs to be connected to the computer via the HC-06-USB Bluetooth virtual serial port.
The HC-02 can be connected to the computer's own Bluetooth device for communication.
you can choose
1 x hc-02 module
1 x hc-02 module with pin
1 x hc-02 module with bottom board
FAQ
1. Is Sunhokey a factory or trading company?
Sunhokey is a direct factory with ISO9001, SGS, TUV proved.
2. What payment way is available by Sunhokey ?
T/T, Paypal, Western Union are good.
3. What is your term of delivery?
We accept EXW, FOB Shenzhen or FOB Guangzhou. You can choose the one which is the most convenient or cost effective for you.
4. What about the lead time for mass production?
Honestly, it depends on the order quantity and the season you place the order.
5. Do you offer a guarantee for the products?
Yes, we offer a 1-year warranty for our products.
6. Do you have any certificates on your products?
Yes, our factory proved by ISO9001, SGS, TUV; our 3d printer filament passed RoHS, REACH; our 3d pen passed CE, FCC, RoHS.
7. Is it possible to do a customized order?
Yes, OEM, ODM, are welcome, customize your own brand, logo and package box are our strong point.
8. Could you send products to my country?
Yes, we do business in every corner of the world, please contact us to consult the details delivery charge.
9. If outside of China(Mainland), must I pay customs duties, import taxes, VATS, etc...?
Yes, customs fees, import taxes, and VAT may apply and not include in your order total cost. Please kindly know that we could not estimate your countries' import taxes. I would suggest you try a duty estimating website like Duty Calculator. |
|
Audited Supplier 
){kind=link}